# Setting Up Your Zwift Ride Smart Frame

> Are you ready to level up?! After setting up your compatible trainer, follow these steps to add your Zwift Ride Smart Frame. Check out our set up videos...

Source: https://support.zwift.com/en_us/setting-up-your-zwift-ride-smart-frame-B1nkgMG8A

Last updated: 2026-02-10T00:54:37.006Z

# Setting Up Your Zwift Ride Smart Frame

Are you ready to level up?! After setting up your [compatible trainer](https://support.zwift.com/zwift-ride-smart-frame-trainer-compatibility-ByuZ01ps0), follow these steps to add your Zwift Ride Smart Frame.

Check out our [set up videos](https://uk.zwift.com/pages/zwift-ride-setup) depending if you bought the [Zwift Ride with KICKR CORE](https://www.youtube.com/watch?v=8AUtw1kqaxY&t=1s) (Zwift Ride) or the [Zwift Ride Smart Frame](https://www.youtube.com/watch?v=qyJ1DHVFyiw) (Zwift Ride Frame Only).

If you bought the Zwift Ride with KICKR CORE and need help setting up your Wahoo KICKER CORE Zwift One, check out our [Wahoo KICKR CORE Zwift One Set Up](https://support.zwift.com/wahoo-kickr-core-zwift-one-set-up-and-troubleshooting-BkY_Cvq6) info.

## Confirming Trainer Setup

First up, you'll want to make sure you have enough space for your trainer, the Zwift Ride Smart Frame, the [device](https://support.zwift.com/supported-devices-to-run-zwift-H1Cj9QbeB) you'll be using to Zwift as well as room to get on and off your Zwift Ride Smart Frame comfortably. We recommend positioning your setup in the middle of a space at least 47" (1.20m) wide and no less than 60" (1.5m) long. You may need more space depending on your individual setup.

Before mounting your Zwift Ride Smart Frame on your trainer, confirm the following:

1.  Your location has the following:
    
    *   A strong wireless network signal.
        
    *   Access to a wall outlet—you'll need to plug in the trainer and charge the handlebar controllers.
        
    *   Good ventilation.
        
    *   Also, while they're not required, it's a good idea to have a fan available to cool your room, and a [training mat](https://us.zwift.com/collections/all/products/zwift-training-mat?variant=43118042808576) to protect your floor.
    
      
    
2.  Your trainer is on a flat level surface and it's seated firmly and doesn't move.
    
3.  You have a [Zwift Cog installed](https://support.zwift.com/en_us/installing-a-zwift-cog-S1EqREQa) on your trainer.
    
    Do not mount your Zwift Ride Smart Frame on a trainer with a cassette.
    
4.  Your Zwift Cog sprocket position is set to number 1.
    
    Check out our article for info on [adjusting the Zwift Cog Sprocket](https://support.zwift.com/en_us/adjusting-your-zwift-cog-sprocket-BJxSF4VrZe).
    
5.  You have the necessary thru axle adapters installed on your trainer.
    
    *   The drive side thru axle adapter is installed.
        
    *   The non-drive side thru axle adapter is installed.
        
    
    If you have quick release adapters installed on your trainer you'll need to remove them and install thru axle adapters.
    
    If you have a Zwift Hub and can't find your thru axle adapters—these came on the green instruction card—[reach out](https://support.zwift.com/contact/contact-us-HJH8N4RNQ) to us for replacements.
    
    ![Trainer Adapter Locations](https://content-cdn.zwift.com/support/EN/Hardware/Resources/Images/Trainer%20Adapters.png "Trainer Adapter Locations")
    
6.  Your trainer's firmware is up-to-date.
    
    You may need to download the trainer manufacturer's app from the [Google Play Store](https://play.google.com/store/apps?utm_source=na_Med&utm_medium=hasem&utm_content=Nov0520&utm_campaign=Evergreen&pcampaignid=MKT-EDR-na-us-1707532-Med-hasem-ap-Evergreen-Nov0520-Text_Search_BKWS-id_100470_%7CEXA%7CONSEM_kwid_43700023142507457_adgroupid_44836427956_keywordid_kwd-294868089100&gad_source=1&gclid=CjwKCAjwuMC2BhA7EiwAmJKRrG0f3b0o4Y_bWs29SodKFf5islldI1MUuuWXlP1O7ue5iiKeJjCR1xoCZvsQAvD_BwE&gclsrc=aw.ds) or the [iOS App Store](https://www.apple.com/app-store/) to update your trainer's firmware.
    

## Installing a Riser Foot

If you need to install one of the included riser feet on your Zwift Ride Smart Frame, you'll do that now. You can check if you need to install a riser foot in our [Zwift Ride Smart Frame trainer compatibility](https://support.zwift.com/zwift-ride-smart-frame-trainer-compatibility-ByuZ01ps0) article. To install a riser foot, follow these steps:

If you bought the Zwift Ride with KICKR CORE, jump ahead to [mount your Zwift Ride on the trainer](#Mounting_Your_Zwift_Ride_on_the_Trainer). Zwift Ride riser feet are not included or required with the Wahoo KICKR CORE Zwift One.

1.  Open the Zwift Ride Smart Frame boxes and remove all of the items from inside.
    
    The smaller Zwift Ride branded box notes "START HERE" on the top. We recommend starting with that box, but, don't worry if you've opened something else first.
    
2.  Carefully lay your Zwift Ride Smart Frame on its side.
    
3.  Using your frame key unscrew both bolts from the bottom of the front foot.
    
    ![Riser Foot Bolts](https://content-cdn.zwift.com/support/EN/Hardware/Resources/Images/Riser%20Foot%20Screws.png "Riser Foot Bolts")
    
4.  Remove the bolts and the foot from the Zwift Ride Smart Frame.
    
    Keep the bolts and washers safe, if you're installing a small riser foot, you'll need them again.
    
5.  Insert the appropriate sized riser foot for your trainer.
    
    *   If you're installing the small riser foot, insert the bolts and washers you previously removed.
        
6.  Using your frame key, tighten the bolts.
    

## Mounting Your Zwift Ride Smart Frame on the Trainer

Follow these steps to mount your Zwift Ride Smart Frame on your trainer:

Do not mount your Zwift Ride Smart Frame on a trainer with a cassette.

1.  If you haven't already, open the Zwift Ride Smart Frame boxes and remove all of the items from inside.
    
    The smaller Zwift Ride branded box notes "START HERE" on the top. We recommend starting with that box, but, don't worry if you've opened something else first.
    
2.  Position the rear dropouts of the Zwift Ride Smart Frame onto the adapters.
    
    Check that your rear dropouts are properly seated on the adapters.
    
3.  Insert the thru axle from the drive side through the Zwift Cog on the trainer.
    
4.  Use the frame key to tighten the thru axle.
    
    ![Install and Tighten Thru Axle](https://content-cdn.zwift.com/support/EN/Hardware/Resources/Images/Installing%20Thru%20Axle.png "Install and Tighten Thru Axle")
    
5.  Follow these steps to place the chain on the Zwift Cog.
    
    Do not add chain lubricant to the chain on your Zwift Ride. The chain is pre-lubricated to the correct specification.
    
    1.  Pull the chain tensioner—the orange circle—down to loosen the chain.
        
    2.  Move the chain over and set it on the Zwift Cog.
        
    3.  Pull the chain tensioner back up to re-tension the chain.
        
        ![Lift Up Chain Tensioner](https://content-cdn.zwift.com/support/EN/Hardware/Resources/Images/Tension%20Chain.png "Lift Up Chain Tensioner")
        

## Assembling Your Zwift Ride Smart Frame

Now that your Zwift Ride Smart Frame is on the trainer, follow these steps to assemble the rest of the Zwift Ride Smart Frame:

1.  Install the handlebar post:
    
    1.  Insert the handlebar post into the front leg, with the tray facing forward.
        
        You may need to loosen the bolt on the front of the front leg to insert the handlebar post.
        
    2.  Using the [bike fit](https://support.zwift.com/en_us/adjusting-your-zwift-ride-SyUBRM8A) recommendation card set the handlebar post to the appropriate letter for your height.
        
    3.  Once you have the handlebar post in position, use the frame key to tighten the bolt on the front of the front leg.
        
        *   If you have a torque wrench, tighten the adjustment bolt to 10Nm.
            
        
        ![Tighten Handlebar Stem in Place](https://content-cdn.zwift.com/support/EN/Hardware/Resources/Images/Tighten%20Handlebar%20Stem.png "Tighten Handlebar Stem in Place")
        
2.  Install the handlebar controllers:
    
    1.  Using the frame key, unscrew the bolt from the bottom of the cap at the end of the handlebar post and remove the cap.
        
    2.  Position the handlebar controllers with the orange paddles facing forward.
        
        ![Install Handlebar Controllers](https://content-cdn.zwift.com/support/EN/Hardware/Resources/Images/Install%20Handlebar%20Controllers.png "Install Handlebar Controllers")
        
    3.  Lift the tray and slot the handlebar controllers into the track under the tray.
        
        You may need to loosen the bolt on the bottom of the handlebar controllers to allow it to slide into the track.
        
    4.  Using the [bike fit](https://support.zwift.com/en_us/adjusting-your-zwift-ride-SyUBRM8A) recommendation card set the handlebar to the appropriate letter for your height.
        
    5.  Once you have the handlebar controller in position, use the frame key to tighten the bolt on the top of the handlebar controller.
        
        *   If you have a torque wrench, tighten the adjustment bolt to 10Nm.
            
        
        ![Tighten Handlebar](https://content-cdn.zwift.com/support/EN/Hardware/Resources/Images/Tighten%20Handlebar.png "Tighten Handlebar")
        
3.  Reinstall the cap, or, if you have a tablet holder, install that now instead of the cap.
    
    1.  Insert the cap, or tablet holder, into the end of the handlebar post.
        
        ![Install Cap/Tablet Holder](https://content-cdn.zwift.com/support/EN/Hardware/Resources/Images/Install%20Cap-Tablet%20Holder.png "Install Cap/Tablet Holder")
        
    2.  Reinsert the bolt through the bottom of the cap, or tablet holder and tighten using the frame key.
        
        *   If you have a torque wrench, tighten the adjustment bolt to 10Nm.
            
    3.  Place the phone tray mat, or the tablet tray mat, over the adjustment point for your handlebar controller.
        
        ![Install Tray Mat](https://content-cdn.zwift.com/support/EN/Hardware/Resources/Images/Install%20Tray%20Mat.png "Install Tray Mat")
        
4.  Install the pedals.
    
    Your Zwift Ride Smart Frame comes with pedals, but you can [install your own](https://support.zwift.com/en_us/adjusting-your-zwift-ride-SyUBRM8A) if you prefer.
    
    1.  Match the pedal labeled R with the right crank, labeled R.
        
    2.  Hand screw the pedal into the crank until it's secure—follow the direction shown on the crank.
        
    3.  Using your frame key, tighten the pedal from the other side, again, follow the direction shown on the crank.
        
    4.  Match the pedal labeled L with the left crank, labeled L.
        
    5.  Hand screw the pedal into the crank until it's secure—follow the direction shown on the crank.
        
    6.  Using your frame key, tighten the pedal from the other side, again, follow the direction shown on the crank.
        
        ![Install Pedals](https://content-cdn.zwift.com/support/EN/Hardware/Resources/Images/Install%20Pedals.png "Install Pedals")
        
5.  Place the two cable tidies on the front leg to secure the cable for your handlebar controllers.
    
    ![Install Cable Tidies](https://content-cdn.zwift.com/support/EN/Hardware/Resources/Images/Install%20Cable%20Tidies.png "Install Cable Tidies")
    
6.  Using the [bike fit](https://support.zwift.com/en_us/adjusting-your-zwift-ride-SyUBRM8A) recommendation card set the saddle to the appropriate letter for your height.
    
7.  Store your frame key in the dock on the frame.
    
    ![Store Frame Key](https://content-cdn.zwift.com/support/EN/Hardware/Resources/Images/Store%20Frame%20Key.png "Store Frame Key")
    
8.  Once you're all set you can [connect to Zwift](https://support.zwift.com/en_us/connecting-your-zwift-ride-to-zwift-Bksj0WzIC).
    

## Torque Values

The following table lists the torque values for tightening the adjustment bolts on your Zwift Ride:

![Bolt Tightening Locations](https://content-cdn.zwift.com/support/EN/Hardware/Resources/Images/Torque%20Locations.png "Bolt Tightening Locations")

  

Adjustment Point

Image Location

Torque Value

Cranks

1

45Nm

Handlebar Post

2

10Nm

Handlebar

3

10Nm

Pedals

4

30Nm

Phone Tray/Tablet Holder End Cap

5

10Nm

Seat Post

6

10Nm

Saddle

7

15Nm

Thru Axle

8

15Nm

Ride On.

\-The Team at Zwift